Understanding the Challenge
That is really fascinating, eight channels and only 399, but one of the biggest complaints about it is how difficult the body is to remove the clipless body mounts. In this video, I’m going to show you three things: three techniques that you have to know to make your life easier.
Technique 1: Push and Slide
You have four tabs here, two on each side, and only two hands. The main technique you have to know is to push the tabs with your middle finger to unlock them, and then push the body up to slide it out of the notches. This may take some practice, but it’s essential to master this step for a smooth body removal process.
Technique 2: Flipping and Releasing
After you have successfully unlocked the tabs on one side, carefully flip the body to access the other side. Repeat the same process of pushing the tabs in and sliding the body out of the notches. This symmetrical approach will help you maintain balance and control while removing the body.
Technique 3: Making Modifications
If you find the standard body removal process too challenging, consider making some modifications to the clipless body mounting system. By exploring alternative methods or experimenting with different tools, you can customize the process to suit your preferences and ease of use.
Removing the FMS FCX10 Body
In order to remove the FMS FCX10 body, you will first need to consider the magnet mount that is in place. This can make it a bit more challenging, especially at the rear of the body. However, there are no wires to deal with, as the electricity is magnetically mounted. To start, align the front and rear of the body, then hold the sides wide to ensure they do not interfere with the wheel wells or sliders.
Mounting a Different Body
When mounting a different body on your FMS FCX10, it is important to align the front and rear properly. Make sure that the sides of the new body do not obstruct the wheel wells or sliders. Once everything is properly aligned, push the back and the front of the body until you hear a positive clicking sound, indicating that the body is securely in place.
Tip #1: Alignment is Key
One crucial tip for removing and mounting bodies on the FMS FCX10 is to ensure proper alignment. By aligning the front and rear of the body correctly, you can avoid unnecessary struggles during the process. Pay close attention to the wheel wells and sliders to prevent any obstructions that could hinder the mounting process.
Tip #2: Making the Process Easier
To make the body removal and mounting process easier, consider making modifications to the body posts. By addressing the two notches on each body post, you can eliminate some of the challenges associated with aligning and securing the body. Making these modifications will streamline the process and make changing bodies on your FMS FCX10 a smoother experience.
Tips for Removing the FMS FCX10 Body
One of the first modifications to consider is cutting the body at the first notch. This eliminates the need to navigate through two notches when removing the body, making the process more efficient and hassle-free. By cutting it at the first notch, you can still easily guide the body out using the middle notch as a reference point.
Utilizing Magnets for Easy Removal
Another tip for removing the FMS FCX10 body is to take advantage of the magnets located on the rear. By understanding the three-stage process of removing the body (magnet first, notch second), you can simplify the process even further. Instead of struggling with the magnets, this approach allows for a smoother removal with the use of both hands, making it a quicker and more effective task.
Mounting a Different Body
When it comes to mounting a different body on the FMS FCX10, it is essential to follow a similar approach to ensure ease and efficiency. By applying the same techniques used for removing the original body, such as cutting it at the first notch and utilizing the magnets, you can streamline the process of mounting a new body. This will make it easier to switch between different bodies as needed without unnecessary complications.
Tip 1: Cutting off the tabs
What you can do on your FMS, FCX 10 is on those two tabs here. Just cut them off, cut them off, cut them off at the second Notch. You know that way its not in the way, and what are we doing? We are now going to rely on the magnets to keep it on. These are three magnets.
Tip 2: Using a guide
These are pretty good and we do have a guide. The guide here will help us mount it, but itll also help keep it in place along with the wheel. Well, so magnets are really strong. These are super magnets, really strong on the up and down where theyre weak is the shear okay, but with a guide theres not going to be any Shear uh, so its going to be fine.
Tip 3: Checking the alignment
Lets Ill. Show you what’s going on here. Uh and Ive been tricking you I I already have it on this car, so right here, Im going to align it and then right there putting it on ASA, easier that’s. Why I have an easier time and then okay, let me press the. Let me press on the front. Okay, okay, I didnt press on the rear right, but check this out. It is fine. It is fine Im going to show you, as this video ends Im going to roll this thing on the ground several times to see that it doesnt come off. You know the two notches: even the one notch on the back was completely unnecessary because theres already a very strong magnet there.
Mounting a Different Body
What it does for.
Tip 1: Removing the FMS FCX10 Body
Removing the FMS FCX10 body may seem daunting at first, but it’s actually easier than you think. To remove the body, all you need to do is get your hand underneath it and lift up with a bit of force. There are no locks or notches to deal with, just magnets holding it in place. With a little bit of effort, the body can be easily taken off without the need to press on any tabs.
Tip 2: Mounting a Different Body
If you’re looking to mount a different body on your FMS FCX10, the process is simple. Just follow the same technique used to remove the original body. With the magnets securing the new body in place, there’s no need to worry about it coming off during rough terrain or rollovers. Even if the body displaces slightly, the magnets will guide it back into position.
Tip 3: Reversing the Modification
If you decide that the modification isn’t working out for you and you want to revert back to the original setup, the process is just as straightforward. Simply remove the new body using the same lifting technique and reattach the original FMS FCX10 body. The magnets will secure it in place, ensuring a snug fit and reliable performance on the trail.
Tips on How to Remove Your FMS FCX10 Body
When it comes to removing the body of your FMS FCX10, the process can be quite simple if you follow these tips. First, locate the tabs on the front of the body. Unlike some models that use magnets, the FCX10 body is secured with tabs. Pay close attention to these tabs as you will need to manipulate them to release the body.
Separate Body Mounts Available for Purchase
One of the advantages of the FMS FCX10 is that you can purchase separate body mounts from the FMS website. These mounts are affordable, typically priced at around $3 each. This makes it convenient to experiment with different body styles, as you can easily swap out the mounts to accommodate a new body.
Mounting a Different Body on Your FMS FCX10
If you have another body that you want to mount on your FCX10, the process is straightforward with the availability of the separate body mounts. The FCX10 has a wheelbase of 12.8 inches, so keep this measurement in mind when selecting a new body. Once you have the new body and the appropriate mounts, you can easily attach it to your FCX10 chassis and enjoy a fresh look for your RC vehicle.