Building the World’s Fastest RC Car
In our previous video, we attempted to break the world speed record with our RC car but fell short of our goal. The original plan was to surpass 200 miles per hour, but we only managed to reach 156. However, we are determined to make some adjustments and try again. Let’s take a closer look at this unique build and see what it’s capable of.
A Unique Design
Most speed cars in the RC world have either one or two motors, which are connected to a center transmission and drive shafts that distribute power to the front and rear differentials. However, our car is different. It features twin motor direct drive, where the motors directly drive the differential. This design makes it quite distinct from its counterparts, and no one really knows what this car is truly capable of.
Identifying the Issue
After our previous failed attempt, we analyzed the problem and discovered that it was with the speed controller. There should have been two of these controllers in the car, along with twin motors and twin ESCs (Electronic Speed Controllers). The car was equipped with 12s lipo batteries, which can be upgraded to 24s or even 30s for more power if needed. However, for some reason, the ESC was set up incorrectly, causing the car to slow down prematurely during our last run.
Preparing for Another Attempt
Now that we have identified the issue, we are ready to make the necessary adjustments and give it another try. We will ensure that the speed controller is properly configured with the correct settings, so the car can unleash its full potential. This time, we are hopeful that we will be able to achieve our desired speed and break the world record.
Testing the Limits
In this video, we will capture the whole process of our second attempt. From the moment we start the car to the exhilarating speed it can reach, we will document it all. The anticipation is high as we eagerly anticipate the moment when the car surpasses the 200 mile per hour mark. It’s an exciting journey filled with suspense, uncertainty, and the thrill of pushing the boundaries of RC car speed.
Improving Performance and Addressing Issues: Upgrades and Maintenance for a Powerful Ride
When our car’s power unexpectedly went down to nothing, we had to accept that it was time to move on and focus on another vehicle. Unfortunately, the replacement car also didn’t have the speed we were looking for. Despite reaching around 170 miles per hour, we were still dissatisfied. Determined to find a solution, we decided to transfer the ESC (electronic speed controller) from the first car to the second. This is when we discovered the underlying problem. Now, let’s delve into the details and understand what went wrong.
Resetting and Testing the ESC
After resetting the ESC, we found that it started working perfectly. Excited about the breakthrough, we swiftly reinstalled it in the car and prepared for another run at full power. We were eager to see what this vehicle was truly capable of achieving on the road.
Maintenance Matters: Noticing and Addressing Front Differential Issues
While inspecting the car, we noticed a minor issue with the front differential. Upon close examination, we were able to identify some play in that particular area. To get a better understanding of the problem, we decided to disassemble the front differential and investigate further. In doing so, we uncovered the root cause of the play, which would need to be addressed to ensure optimal performance.
Introducing New Trill Bulkheads for Enhanced Stability
In our pursuit of enhancing the car’s performance, we came across cutting-edge Trill bulkheads in the market. These bulkheads are crafted using 7075 aluminum, known for its strength and durability. By installing these brand-new components, we aimed to secure the differential mounting and achieve a more stable ride overall.
Improving Steering Precision: Servo Upgrade
Despite having an AGF super high-speed servo installed in the car, we observed a lack of torque when there was significant downforce on the front. This led to vague steering, which impacted overall control. To rectify this issue, we decided to replace the existing servo with a high-performance Perfect Past Monster servo. With its impressive 50+ kilos of torque, this upgrade promised to greatly enhance steering precision and responsiveness.
With all the necessary upgrades and maintenance identified, it was time to get down to work. We couldn’t wait to see the results of our efforts and witness the true potential of this vehicle. So, enough talking; let’s start wrenching and hit the road to experience this powerful beast in action.
The Importance of High-Quality Bearings
Improved Performance with Smoother Motion
Precision Fit with German-Made Bearings
Enhanced Durability for Long-Lasting Use
Comparison to Hot Racing Bearings
Final Thoughts on the Upgraded Bearings
The Importance of High-Quality Bearings
When it comes to machinery, one component that often goes unnoticed but plays a significant role is the bearing. The quality of the bearing can make a world of difference in the overall performance and durability of the machine. Whether it’s an automobile, a motorized device, or even a robotic gadget like the one we’re discussing today, having high-quality bearings is essential.
Improved Performance with Smoother Motion
In the case of this particular device, the bearings are responsible for providing smooth motion and reducing friction as the various parts move. Without a properly functioning bearing, the device may experience jerky movements, increased wear and tear, and ultimately a shortened lifespan. It’s crucial to invest in quality bearings to ensure optimal performance.
Precision Fit with German-Made Bearings
To address the issue of bearing failure, the manufacturers of this device have chosen to use German-made bearings. These bearings are known for their precision and durability, making them a top choice for high-end applications. By opting for German-made bearings, the manufacturers have ensured a precise fit and improved performance for their device.
Enhanced Durability for Long-Lasting Use
One of the primary reasons for bearing failure is the constant stress and strain they undergo during operation. This device requires sturdy and reliable bearings to handle the rigorous demands it faces. The newly installed German-made bearings offer improved durability, reducing the chances of premature failure and increasing the overall lifespan of the device.
Comparison to Hot Racing Bearings
Some users of this device may be familiar with hot racing bearings, which have been previously used. While hot racing bearings may look similar, the experience of using them is quite different. Unlike the hot racing bearings, the new German-made bearings provide a much smoother fit without the need for adjustments or compromises. The hot racing bearings were known to crush and require additional measures to prevent damage, whereas the new bearings fit perfectly without any hassle.
Final Thoughts on the Upgraded Bearings
As we have witnessed throughout the installation process, the upgraded German-made bearings have proven to be an excellent choice for this device. From providing smoother motion, precise fit, and enhanced durability, these bearings offer superior performance compared to their hot racing counterparts. It is evident that investing in high-quality bearings is crucial for achieving optimal functionality and longevity in any machine or device.
Achieving the Perfect Fit: Reassembling the Little Hair
Getting all the small details back in place can sometimes be a challenge. However, it is essential to ensure that everything fits perfectly, just like a jigsaw puzzle coming together. In this article, we will take you through the process of reassembling the “little hair” and making it look as good as new.
Front vs. Back: The Similarities
As we tackle the front section of the “little hair,” it’s important to note that the same process applies to the back as well. Although we won’t be filming it, rest assured that the steps will be identical. So, let’s dive right into it and get the job done.
Giving it a Makeover
Before we proceed, there’s one thing we need to address. Remember that crash we had last time? Well, unfortunately, it left a few grazes on our “little hair.” To make it look brand new again, we will be replacing those damaged parts. Restoring its original glory before moving forward is key.
Win a Traxxas X Max: A Chance of a Lifetime!
But wait! Before we continue, we have exciting news for all of you. You have the opportunity to win a Traxxas X Max, courtesy of a competition we’ve set up. The link to the competition will be provided below, giving each of you a fair chance to enter and win this incredible car. It’s fully equipped with all my favorite upgrades and even shares the same Livery as the monster truck and Toms. Act fast, as you only have two days left to enter!
Ready to Rumble: Time to Test It Out
Enough talk, now it’s time to take action. We are currently at the track, ready to rip and see what our “little hair” is capable of. However, it seems that we are experiencing some acceleration issues. It’s crucial to figure out how to properly set up the mgms. With so many complex settings, it can be overwhelming. But with a little patience and experimenting, we should be able to get it up and running smoothly again.
The Moment of Truth: Witnessing Success
Finally, after all the hard work and adjustments, it’s time to see if our efforts have paid off. The moment we hit the gas, the “little hair” roars to life and shows us what it’s truly capable of. The foams seem to be working perfectly, providing the right balance of traction and stability. We stand back and appreciate our reassembled masterpiece.
When it comes to getting everything back in place, attention to detail is vital. By going through each step carefully and with patience, you can achieve a fit that is second to none. So, whether it’s a “little hair” or any other project, remember that persistence and determination will always lead to success.
The Frustrating Experience with the Perfect Music
A Failed Second Run
After a successful speed run, reaching an impressive 166 miles per hour, I decided to give it another go. The anticipation of even greater speeds had me excited as I took the perfect music up the runway again. However, to my dismay, the car came to an abrupt halt, refusing to move any further. It seemed to be struggling, and from a distance, it was difficult to determine the exact issue.
An Unexpected Twist
Frustration grew as I realized the car was not malfunctioning but was instead stuck in reverse. Attempting to retrieve it, a colleague brought it back to where we were. Curiosity got the best of me, and I decided to give it a small test to see if it would respond. To my surprise, it worked. But just as I thought the situation was resolved, the car began screaming at full throttle in reverse. Unfortunately, we were not recording the incident, and the panic of turning it off only added to our troubles.
The Inability to Stop
No matter what actions I took, the car refused to respond. Turning off the transmitter, trying to activate fail-safe mode, none of it made a difference. The car persisted in its reverse frenzy, and we were left scrambling for a solution. Desperate to regain control, we attempted to remove the body of the car, but even the body clips proved difficult to remove in our haste. In the end, we resorted to taping the front to prevent any further air intake.
A Chaotic Resolution
With the car going wild, my colleague, Paul, and I found ourselves holding onto the car, desperately searching for a way to turn it off. The situation was chaotic, and our attempts seemed futile. Despite the challenges, we remained determined to regain control and bring an end to the car’s relentless reverse rampage.
In conclusion, what seemed like a perfect experience quickly turned into a frustrating ordeal. The unexpected reverse mode of the perfect music left us puzzled and struggling for a solution. Looking back, I wish we had captured the incident on film, but in the heat of the moment, our priority was to regain control. Despite the challenges faced, we were eventually able to bring everything under control. This experience serves as a reminder that even the most perfect things can sometimes go awry, leaving us to find creative solutions to unexpected problems.
Are MGM Speed Controllers Dangerous? Finding a Better Alternative
When it comes to speed controllers, safety is of utmost importance. In the case of MGM speed controllers, there have been concerns about their reliability and performance. In this article, we will delve into the issues with MGM speed controllers and explore alternative options that may be more suitable.
The Troubles with MGM Speed Controllers
Many enthusiasts have found MGM speed controllers to be problematic in their setups. One of the main issues is the difficulty in setting them up correctly. They are known to be complex and can be challenging for beginners or even experienced individuals. This has led to frustration and the urge to find better alternatives.
Another major issue with MGM speed controllers is their inconsistent power delivery. During events, some users reported that the controllers initially perform well, but then experience a noticeable drop in power. This can be dangerous, especially when attempting to reach high speeds. Slowing down unexpectedly can lead to accidents and potentially harm the driver or others on the track. This inconsistency has caused many to question the reliability and safety of these controllers.
Seeking a Solution
With these concerns in mind, it is crucial to find a more reliable and user-friendly alternative to MGM speed controllers. It is essential to prioritize safety and performance when selecting the right speed controllers for your needs.
One option worth considering is consulting an expert who specializes in setting up speed controllers. Their knowledge and experience can help ensure that the controllers are configured properly, reducing the risk of malfunctions or accidents. This approach can provide peace of mind and a safer racing experience.
Additionally, exploring other brands and models of speed controllers is essential. Researching customer reviews and recommendations can help identify controllers that have a proven track record of reliability and performance. A thorough evaluation of features, specifications, and ease of use will aid in making an informed decision.
Unpredictable Speed Controllers: A Frustrating Experience
In the world of remote-controlled cars, speed is a coveted trait. Some enthusiasts spend countless hours modifying their vehicles, hoping to achieve mind-blowingly fast speeds. However, there are times when even the most promising setups can lead to frustrating outcomes.
Initial Bench Testing
Before taking a modified car out for a spin, it is essential to conduct thorough bench testing. This step ensures that all the necessary settings are in place for a safe and controlled experience. Unfortunately, this precautionary measure is not foolproof, as was discovered in a recent incident.
An Unexpected Shift
The excitement was palpable as the modified car was unleashed on the track for its maiden run. However, things quickly took an alarming turn. The car inexplicably started moving in reverse, but only the front wheels were affected, leaving the rear ones unaffected. This unexpected behavior created a dangerous and unpredictable situation.
A Quest for Solutions
Dismayed by the car’s erratic performance, the individual behind the modification project decided to take immediate action. Recognizing the potential in the vehicle to reach speeds exceeding 200 miles an hour, alternative speed controllers were deemed necessary. The hope was that by sourcing more reliable controllers and entrusting their installation to an expert, the car’s performance issues could be resolved.
A Glimpse into the Future
While this setback may have dampened spirits, it has not deterred the enthusiast’s determination. In the upcoming videos, viewers can look forward to new, exciting projects. The next installment will feature a high-powered green speed car, boasting an impressive amount of horsepower. The following video will focus on the “speed sausage” – an unconventional name that carries a seemingly impossible goal of reaching 250 miles an hour.
Patience and Anticipation
As with any ongoing series, the outcome of these future endeavors remains unknown. Enthusiasts and spectators alike will have to exercise patience and wait for each episode to unveil the progress made. Will the modifications finally yield the desired results? Only time will tell, but one thing is for certain: the journey to achieve incredible speeds continues, fueled by a determination to overcome challenges and push the boundaries of remote-controlled car performance.
The Impressive Journey Continues
Our journey so far has been nothing short of impressive. From the moment we embarked on this adventure, we knew there were great things ahead. However, even amidst this remarkable progress, we are well aware that there is still much more to come. The horizon continues to beckon us toward new and exciting possibilities.
Achievements that Set the Bar Higher
Throughout this incredible journey, we have achieved milestones that have propelled us forward. Each success has been a stepping stone to even greater heights. From surpassing financial goals to receiving accolades for our exceptional work, we have set the bar higher with every accomplishment. Yet, we are not complacent. We understand that the path to success is paved with constant improvement and innovation.
Unveiling New Innovations
As we move forward, we are thrilled to announce that there are new innovations on the horizon. Our team of dedicated experts has been tirelessly working to bring groundbreaking ideas to life. We cannot wait to reveal these exciting developments that will undoubtedly revolutionize our industry. With a blend of creativity and cutting-edge technology, we are certain that our audience will be astounded by what lies ahead.
Embracing Challenges with Grit
No journey is without obstacles, and ours is no exception. However, we face these challenges head-on with unwavering determination and grit. We recognize that it is during these trying times that true character is revealed, and we are committed to emerging stronger from each setback. We understand that to reach our full potential, we must be willing to confront difficulties and learn from them. It is this resilience that fuels our drive to not only overcome obstacles but to transform them into opportunities for growth.
Building Strong Connections
Our journey would not be complete without the support and collaboration of our valued partners and customers. We deeply appreciate the trust they have placed in us, and we remain committed to nurturing and strengthening these relationships. Whether it is through constant communication, providing exceptional service, or seeking feedback to continually improve, we believe that building strong connections is the foundation of shared success. Together, we will continue to achieve greater heights.
A Future Filled with Promise
As we reflect on our impressive journey thus far, we are filled with anticipation for what the future holds. The possibilities are endless as we strive to push boundaries and make a lasting impact in our industry. With each step forward, we bring with us the lessons learned and the experience gained, fortified by our unwavering passion to continuously surpass expectations.
Conclusion
Building the world’s fastest RC car is no easy task. It requires innovation, determination, and the willingness to face setbacks head-on. While our previous attempt may not have been successful, we have learned from our mistakes and are ready to make the necessary adjustments. With the correct setup and configuration, it’s only a matter of time before our car reaches incredible speeds and makes history in the RC car world. Stay tuned for our next video, where we aim to achieve the impossible and break the world speed record once and for all.
MGM speed controllers have raised concerns among users due to their difficulty in setup, inconsistent power delivery, and potential safety risks. It is crucial to prioritize safety when selecting speed controllers and to consider alternatives that offer reliability and user-friendly features. Consulting experts and conducting thorough research will ensure a safer and more enjoyable racing experience for all.
While we have already achieved remarkable successes, our journey is far from over. The impressive milestones we have reached are merely stepping stones to even greater accomplishments. Each new innovation, every challenge overcome, and every connection built adds to the tapestry of our story. We look forward to continuing this extraordinary journey, fueled by our unwavering determination to make a difference.